MX Pop Filter – Gooseneck Microphone Pop Shield with Clamp

MX Pop Filter u2013 Gooseneck Microphone Pop Shield with Clamp

The MX Pop Filter is a studio microphone accessory that sits between the speaker and the microphone and softens the sharp bursts of air that turn u201cpu201d and u201cbu201d sounds into distracting thumps in a recording. It is a simple, passive tool with no electronics and nothing to switch on: a layered nylon mesh screen stretched across a round frame, held exactly where you need it by a flexible gooseneck and a clamp that grips a microphone stand. For home studios, podcast setups, voice-over booths and conference rooms, it is one of the cheapest upgrades that makes an audible difference to every take.

Why Choose the MX Pop Filter?

Plosives are a physics problem, not a microphone problem. When you say a u201cpu201d or a u201cbu201d, a short puff of air leaves your mouth and hits the microphone capsule, producing a low-frequency thump that no amount of careful gain setting removes. The MX Pop Filter tackles that puff before it reaches the capsule. The first layer of the screen blocks the direct blast, the gap between the layers disperses the remaining air pressure, and by the time the sound passes the second layer the blast is easily contained, while the voice itself passes through with its tone intact. The result is cleaner speech and singing, fewer ruined takes, and less corrective work in editing. Because the filter is entirely passive, it adds no noise, needs no power, and works with any microphone you already own.

Key Features

The MX Pop Filter brings together five practical features that cover the screen, the arm and the mount.

• Layered nylon mesh screen: Nylon mesh reduces p-pops and breath blasts, and the layered construction with a tighter mesh stops plosives while letting the voice through naturally.
• Flexible, ultra-durable gooseneck: The gooseneck bends to the angle you need and holds its position without sagging, so the screen stays put through long recording sessions.
• Universal mic stand mounting bracket: The mounting bracket fits most microphone stands, making the filter easy to add to an existing studio, podcast or conference setup.
• Rugged, secure mic stand clamp: The clamp grips the stand firmly and keeps the filter stable, even when the gooseneck is adjusted between takes.
• Swivel mount for easy installation: The swivel mount makes the filter easy to mount and demount, so you can fit it in seconds and remove it just as quickly when the stand is needed for something else.

Best Suited For

The MX Pop Filter is best suited for podcasters, voice-over artists, singers recording at home, YouTubers, online teachers and anyone recording speech into a condenser or dynamic microphone. It suits home studios and bedroom setups where a treated room is not available, because it removes one of the most common home-recording faults at the source. It is equally useful in offices and conference rooms where a gooseneck or desk microphone is used for meetings and announcements, and in small studios that need a reliable, low-cost pop shield for every vocal session. If your recordings suffer from popping on plosives or from breath noise, this is the accessory to add first.

Setup and Connection Guide

Setting up the MX Pop Filter takes less than a minute and needs no tools. Clamp the mounting bracket onto your microphone stand and tighten it until it is secure. Bend the flexible gooseneck so the round screen sits a few inches in front of the microphone, between the microphone and the speaker, with the mesh facing the speaker. Position the MX Pop Filter so you speak through the centre of the screen rather than around its edge, and adjust the swivel mount until the screen is square to your mouth. There is nothing to plug in and no power supply: the filter works the moment it is in place. Please note that the microphone, the mic stand and any shock mount are given separately and are not included with this filter.

Frequently Asked Questions

Will the MX Pop Filter change how my voice sounds?

No. The layered nylon mesh is designed to block bursts of air while letting the voice pass through, so your tone stays natural. If the screen is placed too close to the microphone it can slightly soften very high frequencies, so keep a small gap between the screen and the microphone and speak through the centre of the mesh.

Does it fit my microphone stand?

The MX Pop Filter uses a universal mic stand mounting bracket with a rugged clamp, so it fits most standard microphone stands. Check that your stand has a straight pole section for the clamp to grip; the gooseneck then lets you position the screen exactly where you need it.

Do I need anything else to use it?

You need a microphone stand to clamp it to, and a microphone to use it with. The microphone, the mic stand and a shock mount are not included, so if you are setting up a recording space from scratch, order those alongside the filter.

Technical Specifications

Complete your setup: Pair the MX Pop Filter – Gooseneck Microphone Pop Shield with Clamp with the Ahuja PGM-481 Microphone and the Akg C414 Xlii Microphone.

Explore Related Products

Pair it with the MX RM01-18 Gooseneck Conference Microphone (18 inch) for clear, focused speech in conference rooms, lecture halls and meeting spaces.